WPC Wood Grain Board - 150 × 25 mm, and the Length That Sets the Job

A Deck Is Sized by the Board, Not by the Square Metre
A deck is quoted in square metres and bought in boards. The two never meet exactly. The gap is where a job runs short, or ends with a stack of offcuts.
This board is 150 mm wide and 25 mm thick, in a co-extruded section, with a groove on both edges. Width sets how many rows cross the deck. Length sets how many boards make a run.
Those two numbers decide the board count, the butt joints, and the offcut at the end of each run.
Nothing on this page is a test result. Slip resistance, fire class and colour fastness are not stated, because no report is held for them on this build.
Weight per square metre is quoted with the order. The board has not been weighed on this line.
Specification Sheet
|
Item |
Figure |
Remark |
|
Section |
150 × 25 mm |
Hollow, co-extruded, grooved both edges |
|
Length |
2,900 mm |
5,800 mm on request |
|
Face area |
0.435 m² a board |
150 mm × 2,900 mm |
|
Boards to the m² |
2.30 |
6.67 m to the m² |
|
Core |
Wood fibre and HDPE |
Cap layer extruded with it |
|
Face |
Wood grain, embossed |
Grain runs along the length |
|
Edge |
Groove both sides |
Takes a clip, or a face screw |
|
Joist spacing |
Quoted with the board |
Depends on thickness and load |
|
MOQ |
300 m² |
2,000 m, or 690 boards |
|
Packing |
Bundle, end-capped |
Count on the packing list |
|
Weight |
Quoted with the order |
Not weighed on this line |
What the Cap Layer Is
The cap is a second compound, extruded through the same die as the core, so the two leave the machine as one section. There is no glue line between them.
That is a statement about how the board is built, not about how long it lasts. A cap changes the surface; it does not replace a test report.
The grain is embossed after the section is formed, so the pattern runs the length and stops at the ends.

The Length Decides the Board Count
A run is one board wide and as long as the deck. Choose the length badly and every run gains a joint and a second board.
|
Deck length |
At 2,900 mm |
At 5,800 mm |
Butt joints a run |
|
2,800 mm |
1 board |
1 board |
None |
|
5,000 mm |
2 boards |
1 board |
One |
|
5,800 mm |
2 boards |
1 board |
One |
|
8,000 mm |
3 boards |
2 boards |
Two |

On a deck shorter than 2,900 mm the short board is the only sensible buy, because the long one gives up more than half its length.
A 4,000 × 5,000 mm deck is 20 m². At 150 mm it takes 27 rows, and 26 full rows come to 3,900 mm, so the last board is ripped to 100 mm.
Run the 2,900 mm board and the job needs 54 boards and 27 butt joints. Run the 5,800 mm board and it needs 27 boards and no joints at all.
A 3,600 × 4,800 mm deck is 17.28 m². It divides exactly: 24 rows at 150 mm, and no rip.
At 2,900 mm each run takes two boards, so the deck needs 48 boards, 24 butt joints and 1,000 mm off every second board. The 54 boards for the 20 m² deck cover 23.49 m², and that is what gets bought.
Length bites hardest at the top end. An 8,000 mm run takes three short boards, which is 8,700 mm, so 700 mm comes off each run.
The material is the same either way: each run gives up 800 mm, long board or short. What changes is the piece count, and how many joints can move.
Where a Butt Joint Is Allowed
A butt joint is only a joint if something sits under it. On a timber or composite frame, that means a joist directly below the joint, and two clips, one either side.
A joint that falls between joists has nothing holding the two ends level. One end lifts, the other drops, and the gap opens from the top down.
So the layout is set before the order, not on site. If a deck is 5,000 mm long, either the joint lands on a joist or the board is bought at 5,800 mm to remove the joint.

The Joint: Hidden Clip or Face Screw

The groove takes a clip that is screwed to the joist and grips both boards. Nothing shows on the face, and the boards are held with a gap set by the clip.
A face screw is the alternative. It goes through the board into the joist, leaves a head visible, and needs a pilot hole at the edge.
The clip is faster on a new deck. The screw is what a repair uses, where a board is already cut short.
Both need a fixing point under the board. Neither works over a gap, and neither is a substitute for a joist.
The Edge of the Deck
The perimeter is where a deck looks finished. It is also where the board is asked to do something it was not made for.
|
Edge condition |
What it needs |
What goes wrong without it |
|
Against a wall |
A gap, and a cover trim |
Water sits, and the board stays wet |
|
Against a lawn |
A solid edge, or a border board |
Soil migrates into the gap |
|
A step down |
A fascia board on the rim joist |
The cut ends of every run show |
|
An outside corner |
Two boards mitred, or a corner trim |
The groove is open to the weather |
|
A board end at the rim |
A joist under it |
The end springs when stepped on |
What the Perimeter Gap Is For
A deck board moves with temperature and moisture, and the frame does not move with it. The gap at a wall is there to give the board somewhere to go.
The size of that gap is quoted with the layout rather than printed here, because it follows the length of the run and the range the site sees.
A board fitted hard against a wall has nowhere to go. It either lifts at a fixing or bows between two of them.

Where It Is Specified

Garden terrace
150 mm, 2,900 mm; 150 × 25 mm co-extruded hollow decking board, natural warm teak finish
A domestic deck, one level. Private villa residential backyard patio deck; 150 mm wide boards run parallel toward lawn with narrow uniform drainage gaps held by hidden clips, barefoot-safe and splinter-free.
The run length, and where joints fall (choosing 2,900 mm lengths to eliminate offcuts and landing butt joints directly over double joists).

Roof terrace
150 mm, 5,800 mm; 150 × 25 mm co-extruded decking board, modern smoked grey finish
A deck over a membrane. Penthouse rooftop entertainment deck installed on adjustable pedestals over waterproofing membrane; 5.8 m ultra-long boards stretch across the roof without mid-run butt joints.
Height build-up above the membrane (calculating pedestal height, joist thickness, and 25 mm board thickness to match door threshold).

Pool surround
150 mm, 2,900 mm; 150 × 25 mm co-extruded decking board, natural honey teak finish
A deck beside the water. Resort and private swimming pool deck surround; 100% moisture-proof co-extruded cap layer resists chlorine and pool chemicals while providing tactile slip-resistant embossed wood grain.
The gap, and what is under it (uniform drainage gap allowing splashed water to drain instantly, and corrosion-resistant 316 clips).

Restaurant terrace
150 mm, 5,800 mm; 150 × 25 mm heavy-duty decking board, rich dark walnut finish
A deck under tables. Waterfront restaurant outdoor dining patio; heavy-duty hollow section with co-extruded stain-resistant cap layer withstands chair-leg point loads and food/wine spills.
Chair legs, and point loads (specifying joist spacing at 300 mm centres under heavy commercial dining loads).

Boardwalk
150 mm, 5,800 mm; 150 × 25 mm co-extruded decking board, weathered natural oak finish
A long run, few joints. Public park waterfront wetland nature boardwalk; 5.8 m continuous boards maximize installation efficiency and minimize end-joint trip hazards in public recreation environments.
The frame, over its whole length (substructure span engineering and expansion gaps at long run intervals).

Balcony
150 mm, 2,900 mm; 150 × 25 mm co-extruded decking board, warm teak finish
A small deck, four edges. High-rise apartment private balcony; boards fitted flush beneath sliding door threshold with hidden drainage below and perimeter fascia trims covering rim joists.
Drainage, and the door threshold (maintaining free water drainage under the deck and flush threshold alignment).

Ramp
150 mm, 2,900 mm; 150 × 25 mm slip-resistant decking board, rich chocolate brown finish
A sloped run. Barrier-free accessible entrance ramp; boards laid perpendicular to slope onto angled joists, providing exceptional tactile grip and slip resistance underfoot in wet weather.
The joists, and how they are cut (cutting substructure joists to the exact gradient and ensuring flush transitions at top and bottom).

Marina pontoon & pier dock
150 mm, 2,900 mm / 5,800 mm; 150 × 25 mm marine-grade co-extruded decking board, natural teak finish
Waterfront floating pontoon pier and yacht berth. Salt-spray and UV-resistant polymer cap layer withstands continuous marine exposure without rotting, splintering, or algae growth.
Marine-grade 316 stainless steel clip fixings and water-level rise clearance.
Against Timber Decking, Composite Tile and Stone Paving
|
Point |
Timber decking |
Composite tile |
Stone paving |
WPC board |
|
What goes down |
Joists, then boards |
Pedestals, then tiles |
Mortar bed, or pedestals |
Joists, then boards |
|
Piece count |
High, boards and fixings |
High, one tile at a time |
High, and heavy |
Low, one board a run |
|
Water at a joint |
Sits, and the timber takes it |
Drains at the gaps |
Sits on the bed |
Drains at the gap set by the clip |
|
Surface |
Sanded and oiled |
Matched to the tile |
Cut stone |
Embossed grain |
|
Fixing |
Screws, visible |
Hidden clips under the tile |
Bed or pedestal |
Hidden clip in the groove |
|
Taking it up |
Screws out, boards lift |
Tiles lift |
Demolition |
Clips out, boards lift |
|
Repainting |
Every few years |
Not part of it |
Not part of it |
Not part of it |
|
Where it loses |
Water, and the maintenance |
Height build-up, and cost |
Weight, and a wet trade |
It needs a frame under it |
Stone wins on a flat base and loses on everything a frame has to carry. A board deck spreads the load onto joists.
How a Run Is Made and Checked
Extrusion, embossing, cut, bundle. The check that decides whether a batch is accepted is the cut. A board at 2,895 mm leaves a 5 mm gap at the end of every run.
That error accumulates. By the tenth run it is a visible stepped edge, and no clip adjustment closes it.
The Inspection Plan
|
Stage |
Checked |
Recorded |
|
Section |
Dimensions at the groove and the web |
Batch sheet |
|
Cap |
Coverage across the face and both edges |
Line check |
|
Grain |
Emboss against the retained master |
Master board |
|
Groove |
Full slot, and a clip that seats |
Sample joint |
|
Cut |
Length, and a square end |
Bundle ticket |
|
Loading |
Bundles and end caps before the doors shut |
Photographs |
Two documents travel with the goods: the packing list and the photographs taken at the doors. Ask for both before releasing the balance.
Terms, Packing and Paperwork
Quote
Boards, clips, trims and packing on separate lines, in metres and square metres. FOB or CIF, as the buyer prefers.
Take-off
Send the deck as length and width, with the board direction. The board count, the joint count and the offcut come back together.
MOQ
300 m², which is 2,000 m or 690 boards of the 2.9 m cut.
Sample
A cut length and a joint pair, so the clip can be tried before ordering. No charge, courier at cost, 3–5 days, credited on the first order.
Claims
A crushed bundle is settled against the loading photographs and replaced on the next shipment. Report it inside 7 days of arrival.
Private label
Artwork printed on the bundle above the 300 m² minimum, at no extra cost. The face carries no brand.
Repeat colour
Quote the batch number and the face is run against the master we kept. Without it, the current batch.
Payment
30 per cent with the order, 70 before shipment, or an L/C at sight. Loaded at Ningbo or Shanghai.
Packing and Claims

A 20' GP measures 5.898 m inside. Two 2,900 mm boards end to end come to 5,800 mm, which leaves 98 mm at the doors, so the load runs along the floor and nothing turns once it is in.
A 5,800 mm board fills that length alone. The short cut ships as two.
Where a project needs a slip figure, a fire class or a colour-fastness statement, say so before the order is booked. This build holds none of the three.
FAQ
Q: How does board width affect the number of boards I need?
A: At 150 mm, a wall or deck takes 2.30 boards per m². A 100 m² area needs 230 boards; a 300 m² order needs 690 boards at the 2,900 mm cut. The board count, joint count and offcut come back together when you send the run length and width.
Q: Is a butt joint visible or hidden?
A: Both ends sit on a joist, with two clips, one either side. A joint that falls between joists has nothing holding the two ends level, and the gap opens from the top down. On a 5,000 mm run, either the joint lands on a joist or the board is bought at 5,800 mm to remove the joint.
Q: What is the MOQ, and can I try a joint before ordering?
A: MOQ is 300 m² - 2,000 m or 690 boards of the 2.9 m cut. A sample of the cut length and a joint pair is sent so the clip can be tried before ordering. No charge; courier at cost; 3–5 days; credited on the first order.
Q: How does a 20′ container load 2,900 mm boards?
A: The 20′ GP measures 5.898 m inside. Two 2,900 mm boards end to end come to 5,800 mm, leaving 98 mm at the doors. The load runs along the floor and nothing turns once it is in.
Q: Do you hold fire, slip or colour-fastness reports for this board?
A: No. This build holds none of the three. If the project needs a slip figure, a fire class or a colour-fastness statement, say so before the order is booked.
Hot Tags: WPC Wood Grain Board, China WPC Wood Grain Board manufacturers, suppliers, factory, wpc wall panel mexico, harga panel wpc, panel wpc interior, wpc marble wall panel, wpc wood panel, wpcpanel
